Plant Works & Engineering March 2022

I n recent years, bearing manufacturers have increasingly focused on creating energy-efficient bearings — making use of new materials, lubrication techniques and advanced geometry designs to reduce losses without sacrificing the load carrying capacity. However, energy losses in bearings are not considered the primary focus of plant optimisation efforts because they are already considered a high efficiency component. On the other hand, some argue that bearings are so ubiquitous — with a huge number of installed bearings in industry — that this overall energy consumption and potential energy savings should not be ignored. Let’s take a closer look at three bearing design considerations to decrease friction and increase efficiency. Advanced materials Energy-efficient bearing designs focus primarily on reducing the contact between the rolling elements and the raceways or the cage. By reducing the roughness of the contacting elements, friction will be reduced. Furthermore, the osculation of the bearing at both the inner and at outer rings significantly effects the friction by reducing the contact area and thus the microsliding of the contact. According to a 2021 study, friction-optimised designs can have a significant impact on the reduction of the global energy losses of bearings. Based on the design of one bearing manufacturer, a preliminary estimation of this reduction is about 0.15 – 0.20% of global energy consumption. Traditionally, steel has been the material of choice in bearing design, but polymer-based materials, such as PTFE and nylon, offer many benefits when used in less demanding environments. These benefits include corrosion resistance, reduced need for lubrication and a reduced weight. Geometry Geometry considerations such as special cage designs and the number of balls in a bearing influences the amount of friction generated, as this determines the number of frictional contacts during operation. The geometry, as well as the process by which the retainer is manufactured, have an influence on the friction generated. For example, opting for a 3D printed retainer in nylon (PA66) or another polymer material can help to reduce the weight of the whole bearing. In some cases, ceramics offer a feasible alternative to metal. They have properties that offer similar benefits to metal, but they’re much lighter too. Carbon-fibre reinforced nylon is one of the most popular combinations for nylon-printed materials. It offers many of the same benefits as standard nylon including high strength and stiffness, but it produces significantly lighter components. Surface coatings can have a significant effect on bearing friction reduction. Coatings such as molybdenum disulphide and tungsten disulphide increase wear resistance, fatigue durability, and reduce friction during bearing motion. Lubrication A proper lubricant will reduce friction between the internal sliding surfaces of the bearing’s components and reduce or prevent metal-to- metal contact of the rolling elements within their raceways. While this is a good way of reducing wear and preventing corrosion, there are new materials that, when used on bearings, dramatically reduce friction compared to the lubrication and surface treatment options that are currently on the market. The material in question is graphene. The process of adding a graphene coating to bearings would be relatively simple and similar to adding a traditional lubricant. When graphene becomes readily available, we will examine this form of lubrication more closely. As well as not being harmful to the environment, graphene flakes that are added to the surface of a bearing can last a considerable amount of time, due to the ability of the flakes to reorient themselves during the initial wear cycles, providing a very low coefficient of friction (COF). In a study on the potential of graphene as a new emerging lubricant, researchers estimated that the reduced loss of energy to friction offered by new materials would yield potential energy savings of 2.46bn kilowatt-hours per year, equivalent to 1.5m barrels of oil. By optimising each element of a bearing’s design to consider friction, it is possible to reduce bearing friction. By multiplying this saving for each bearing in a machine, plant or industry, significant energy savings can be realised. * Chris Johnson is managing director at SMB Bearings Process, Controls & Plant Focus on: Seals, Bearings & Lubrication 34 | Plant & Works Engineering www.pwemag.co.uk March 2022 Three bearing design considerations to reduce friction It is estimated that a 10% reduction of friction in all large bearings in use would provide an energy saving equal to the output of 18 large power stations. Cutting friction in bearings of any size is a key method to improve energy efficiency. Chris Johnson* explores the bearing design possibilities for increased efficiency in industrial applications.