COMPRESSED AIR, VACUUM, AND GENERATORS approximately 7% of the full load power. Additional generation of pressure will also lead to additional storage capacity and increase the cost of equipment. Pressure drop upstream of the compressors created by the inlet air filter system results in higher power consumption. A pressure drop downstream will induce the need to select a compressor system that generates a higher pressure. Air pressure optimisation, and minimising differentials in all parts of the system are important criteria for efficient operation and saving energy. If a certain side application requires a much higher or lower pressure, it is advisable to use a separate compressed air system for that pressure rather than expanding or boosting the compressed air from the central system in a factory. The ROI of a separate system will be economical compared to the overall energy savings that the plant would generate by optimising pressure requirements. Choosing the right components in a compressed air system Compressed air contains inherent impurities that are detrimental to the end application. Some common contaminants of compressed air are water, dirt, small wear particles, bacteria, and sometimes even degraded lubricating oil. For increased reliability and energy savings, compressed air must be clean and dry. Choosing the right product from a wide range of pneumatic downstream and upstream accessories can make the air friendly to the environment, end-use, and your pocket: Moisture and water vapour precipitate as condensate when compressed air cools down following a compression process. Dryers eliminate and remove this condensate from the compressed air system to prevent damage to downstream equipment. In the case of oil-lubricated screw compressors, the process of compressing air results in the formation of condensate, a mix of water, oil, and dust particles. To avoid polluting the groundwater, it is necessary to treat the condensate before disposal into the wastewater system. An Oil Water Separator can be easily integrated into any installation and removes oil in the condensate through a multi-level separation process with both efficient, absorbent fibre and activated carbon, only using gravitational energy. Atmospheric air contains moisture, particle contaminants, microorganisms, and gases. When it is compressed, the concentration of these elements 36 HYDRAULICS & PNEUMATICS March 2024 www.hpmag.co.uk 30% of energy, increasing the company’s operating costs. When selecting the unit for your facility, duty cycle, operating pressure, and airflow demand should be some of the key considerations. Different industries like pharmaceuticals, automotive, food and beverage, etc. are powered by various pneumatic applications that demand a specific airflow (m3/min). Selecting a suitable compressed air system is crucial to ensure that the air compressor meets the airflow and pressure demands of the pneumatic applications while ensuring optimal performance and energy consumption. The duty cycle, referring to the operation cycle or the time the compressor runs to provide compressed air at a consistent pressure and specific flow rate, is one of the critical parameters that help decide if a fixed speed drive or a variable frequency drive (VFD) is required. Manufacturers can choose from a wide range of air compressors equipped with or without a VFD based on the variation in airflow demand. In the case of a fixed-speed air compressor, the compressor runs at the same rate, consuming the fixed power for the air demand. The electrical motor runs at the maximum constant speed irrespective of the compressed air requirement. On the other hand, the air compressor with variable frequency drive can automatically adjust the speed between its minimum and maximum range, ensuring that the compressed air generation matches the compressed air demand and subsequently consumes significantly less energy at low demand. The VFD air compressor greatly benefits industries and applications with largely varying airflow demands. However, it’s not a given that a VFD compressor is the better technology in all cases. It’s important to look at the size of the air receiver that provides a certain buffer capacity. This air receiver will ultimately handle smaller flow fluctuations and therefore will be very beneficial to avoid too frequent starts of the compressors, and even help VFD compressors as too fast of air demands will lead to quick pressure drops which the VFD cannot cope with. Therefore, there is a good consideration to be done when auditing and changing eventually the system after an audit. When pressure drops Selection of the right compressor can be a daunting challenge with several technologies and options available in the market. Looking at the quality of air requirements, the capacity of the compressor, duty cycle, and utilisation together with your compressed air partner will help you choose the right solution. Whether it’s reciprocating and screw compressors, VFD, or Fixed Speed technology, one of the other factors to look at is the overall design of the system and reduction of pressure drops – the reduction in air pressure from the compressor discharge point to the application point of usage. High-pressure drop in the distribution system and the hoses, pipes, and joints results in lower operating pressure to the user and thus results in additional pressure generation and a significant increase in energy consumption. The most typical areas where “Pressure drop” occurs include the pressure vessel, aftercooler, air treatment equipment like dryers, filters, check valves, and the piping system itself. For every additional 1 bar increase in discharge pressure, there will be an additional energy consumption of
RkJQdWJsaXNoZXIy MjQ0NzM=